Asterisk Analog card TDM410PL 4 FXO/FXS PCI interface Voip Digium for 2U version

Asterisk Analog card TDM410PL PCI-E 4 FXO/FXS 2U compatible with DIGIUM Support trixbox elastix freepbx 

Introduction

Overview
 

TDM410P is a new generation analog card with interchangeable
FXS_100  and FXO_100 modules. It can eliminate the requirement for separate
channel banks or access gateways.
 

TDM410P contains 4 module banks. Each bank
supports one analog interface. The module banks may be filled with up to FXO_100 or
FXS_100 modules enabling the creation of any combination of ports. Scaling of an
analog card solution is accomplished by simply adding additional cards.
 

TDM410P
works with Asterisk®, Elastix®, FreeSWITCH™, PBX in a Flash, trixbox®, Yate™ and
IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR,
and VoIP gateway applications.
 

Main Features:

*  High security: It adopt tertiary
thunder preventing technology, can prevent the thunder and lightning from striking
effectively

*   No additional power connector or supplier is required for the operation
of FXS modules, reduced the line wave of the power, has improved the voice quality.

*
32 bit bus master DMA data exchanges across PCI interface at 132Mbytes/sec for
minimum host processor intervention.

* The high stability firmware is exported /
imported with DMA data exchange, so it accelerated and reduced CPU load greatly.
Under the environment of the same hardware, CPU rate of utilization is equal to CPU
rate of utilization of using 4 port analog card.
 

*  World Wide Usable: Configurable line
interface to meet global telephone line interface requirements.

*  Support all functions
of Asterisk PBX system needed.

*   Exchangeable with Digium modules: It is mixable
with X100M/S100M of Digium.

*   Easy to install: Both software and hardware
compatible with Digium Asterisk card.

*   Humanization is designed: The module
socket that should be nipped is all adopted and stuck to one slice of sockets, can
prevent stabing users finger effectively.

 New function:
 

*   Easy to install , using way
is same as DIGIUM Asterisk card
 

*   If use Trixbox/Elastix/Freeiris2 IPPBX software, it
can automatic recognition our cards, don’t need to install any drivers.
 

 Product
Spotlight
 
TDM410P is a new analog card. It can be used for connecting analog
telephones and analog POTS lines through a PC. It delivers the superior voice quality
on both FXO and FXS interfaces in all 4 ports.
·  Adjustable Interrupt Routing Design
· 
Interrupts Frequency Adjustment
·  Up to 4 Simultaneous PSTN Calls (Per PCI Slot)
· 
Compatible with All Commercially Available Motherboards
·  3-Month “No Question
Asked” Return Policy
·  Lifetime Warranty
 
Target Applications
 
·  Channel Bank
Replacement / Alternative
·  Small Office Home Office (SOHO) applications
·  Small and
Medium Business (SMB) applications
·  Gateway Termination to analog
telephones/lines
 
Services and Features
 
·  Caller ID and Call Waiting Caller ID
·  ADSI
Telephones
·  Loopstart Signaling Support
 
Technical Specifications
 
·  Up to 4 ports
through a combination of FXS_100 and FXO_100 modules
·  Full-length analog card
· 
Up to 1 quad FXS or FXO modules
·  RJ45 connector
·  32-bit 33MHz PCI and fully PCI
2.3 compliant, compatible with all commercially available motherboards, and proper
sharing of PCI interrupts
·  32 bit bus master DMA data exchanges across PCI interface
at 132 Mbytes/sec
·  Autosense compatibility with 5 V and 3.3 V PCI busses
compatible
·  Power: 8.21W Minimum, 88.24W Maximum at 3.3 V or 5 V.
·  Operation
temperature: 0°C to 50 °C
·  Storage temperature: -40°C to 125°C
 
Operating Systems
 
·  Linux (all versions, releases and distributions from 1.0 up)
 
Minimum Hardware
Requirement
 
·  800-Mhz Pentium III
·  128MB RAM
·  Available PCI Slot
 

Size and Weight

Size(L*W*H): 214*105*12MM

Weight: 242g